After you have your printer all set up, you can load a model to slice. Slicing with a resin printer is quite a bit different from slicing for a traditional FDM printer. Since the model is printed upside down and is printed used liquid resin, there are additional things you need to take into account such as drainage holes, the weight of the item you are printing so it doesn’t fall off the build plate, and even where the supports attach so that when they are removed, you don’t remove delicate details. Saturn 2 includes 12 new distortion styles, a radically overhauled and expanded modulation system, enhanced envelopes, linear phase processing, and a new ‘Superb’ High-Quality mode. The new distortion styles, nearly twice as many, included ‘Subtle’ versions of the Tape, Tube, and Saturation styles for warmth and four new guitar amplifiers, three Transformer styles. All of this means that you use Saturn 2 for everything from sweetening a mix bus through to guitar amp simulation. After printing, the model will still likely have some leftover resin on it and, to get a resin print to look its best, you will want to clean it. Distortion and saturation play a very important role in music production. From subtle, clean and warm tube or tape saturation to the wildest multiband guitar amp effects: FabFilter Saturn 2 delivers.

To get your model prepared, you will want to place the model at an angle. Placing models at an angle makes it much easier to remove them from the build platform without damage in the process. It also gives more surface area for supports to hold on so the model is less likely to fall during printing. Fully redesigned, easy-to-use interface, including a new design of modulation sources and floating slot panel One of the most obvious improvements of the Elegoo Saturn 2 is the 8K high resolution screen. The screen is 10 inches, which is a noticeable improvement over the 8.9-inch screen on the original Saturn and the 9.1 inch display that came on the Saturn S. The popular Elegoo Saturn gets another new edition: the Elegoo Saturn 2! The successor is equipped with a huge 10-inch 8K monochrome LCD, allowing for even larger and more accurate prints. The huge build volume of this MSLA-3D printer makes it possible to print detailed, large-format objects.

There was a large payload gap between the Saturn IB's 46,000-pound (21,000kg) low Earth orbit capacity and the Saturn V's 310,000-pound (140,000kg) capability.

Monochrome LCD】 ELEGOO Saturn 2 adopts a 10-inch 8K mono LCD screen with an HD resolution of 7680x4320 and an ultra-fine XY resolution of 28.5 microns, outputting outstandingly detailed 3D models with a cure time of only 1-3s per layer. The scratch-resistant tempered glass above the LCD screen with 9H hardness for better light transmission and protection. Finally, FabFilter Saturn 2 contains all the usual FabFilter goodies: perfectly tuned knobs, MIDI Learn, Smart

The Saturn 2 is equipped with dual linear rails along the Z-axis, which ensure high stability. The movements of the build platform run smoothly. The MSLA 3D printer allows you a Z-axis resolution of up to 0.00125 mm. Once that is complete and you have removed the hardened resin, you should empty the resin tank. The plastic spatula works well to assist with this. Emptying the resin first allows you to inspect the FEP film as well. If it gets too damaged, you may need to replace it before continuing. To wash the models, I used Elegoo’s largest Wash and Cure station, the Mercury X bundle. Although this was designed with the original Saturn and Saturn S in mind, which have slightly smaller build volumes, I found the build platform still fit into the tank. The only issue I had was with some of the taller prints bottoming out. Prints can and eventually do fail even on resin printers, though I did not experience any failed prints on the Saturn 2 myself. Whether it happens due to support structures that are unable to support the mass or any number of other things, you still will have a mess to clean up before you can print again.

This is a very polished machine that produces prints of phenomenal quality. During the entire time I was testing it, I had no failed prints. If you are looking for a mid-sized 3D resin printer or you need to print in a high level of detail, you really can’t go wrong with this printer. AWIN, Sovendus, Meta-Pixel, Google Ads, Microsoft Advertising, creativecdn.com (RTBHouse), Ads Defender The metal spatula is for helping to remove your prints from the build plate and you want to be careful while doing so, as it can potentially gouge or scuff the metal surface. The soft spatula is used more as a tool for cleanup such as assisting with removing any residual resin out of the resin tank when emptying.

It also comes with a set of hex key wrenches and some spare screws in case any servicing or repairs need to be performed during the printer’s lifetime. There are two pairs of latex gloves and two surgical style masks for personal protection, but you will probably want to get some higher quality masks and additional gloves for working with resin. Before any version could be put into production, work on all Saturn variants was stopped in favor of launching all future payloads from the Space Shuttle. Leveling the printer was pretty straightforward. The first step is to loosen the two bolts on the sides of the resin tank. Then using the control panel on the front of the printer, you want to raise the build platform to a sufficient height that the resin tank can be removed. With some of Elegoo’s earlier printers, this guessing has yielded softer prints that were often gouged with the spatula upon removal. It appears that the company has increased the exposure time with the latest test prints, so it takes a bit longer, but the model is less likely to be damaged. After that, run a tank clean cycle through the printer’s menu, which will expose the entire bottom layer of the tray to UV light and create a solid mass of any little pieces that may have broken off of the failed print. You may consider adding a piece of removed support from a previous print to one corner first to make removal of the mass easier.