Silverline Soldering Sponges 10pk (633932)

Product Information

They can also provide you with all the essential soldering equipment you need, from preheaters to consumables. With over 90 years of experience in the electronics industry, JBC leads the way in delivering innovative, high-quality and cost-effective soldering products. Some people say that they are not as gentle as soldering sponges because they tend to scratch and damage the tips due to friction. While this can happen when they are not used carefully, they are almost as harmless as wet sponges in terms of friction. To extend your soldering iron equipment in general, you should always avoid working at high temperatures for extended periods of time. When not in use, make sure that your soldering iron is on an ‘idle’ setting or turned off completely. There are some soldering irons that will automatically lower their temperature when not in use. The strength of the soldering joint is relatively low. Soldering is commonly used in electric and electronic applications, Sheet metal work wire terminals, sealing of metal containers, and similar small parts.

Desoldering is the process of removing hardened solder material from a previously soldered joint, surface or component. With enough care and expertise, this can be done using a regular iron - however, a number of dedicated tools and desoldering accessories exist for making the job much easier and neater. These include: Cleaning a soldering iron bit is an important part of any soldering job. This process helps to ensure the highest quality results, as well as preventing damage to your iron and the pieces you are soldering together. Cleaning your bit should be done after every use, or whenever you switch from one type of solder or wire to another. Here’s how it’s done: Read all product instructions and safety guidelines thoroughly, and make sure you’re aware of the common risks However, a brass wool cleaner is handy when dealing with stubborn debris or trying to save worn-out or old tips. The flux adhered to the wool wire is helpful when the tip is heavily compromised by corrosion, or you unintentionally overheated it.Never touch the soldering iron anywhere except the insulated handle (sometimes referred to as the ‘wand’) Brass wool is an effective soldering iron tip cleaner that can be used to remove dirt and other contaminants that gather as you work. Frequently using a wet sponge can reduce the temperature of your soldering iron tip. If you are working with materials that require a very specific temperature, this could be problematic for your work. The tip tinner / cleaner is a chemical alternative to cleaning and retinning the tip at the same time. It should be used when the other methods fail and a more active cleaning method is needed. What’s the best type of wool? Employing this approach involves heating the iron to soldering temperature, followed by dipping it in a flux container. If you are using liquid flux, a drop or two on the hot tip works as well. Immediately rub the tip onto the moist sponge a few times. Depending on the level of tip oxidation, this should expose some amount of silver tip underneath the dark oxide cladding. If not, repeat the process until that happens. The brass wool is an alternative to the sponge, needs less maintenance but does not decrease tip temperature, which is why it is better suited to sometools with low thermal response. A disadvantage to the brass wool is that it retains residue which in turn may fall on the PCBs if there is no splashguard. The brass wool holder should be heavy enough to avoid having to steady it when being used.

Due to the low temperatures used in soft soldering, it thermally stresses components the least, but does not create strong joints and is therefore unsuitable for mechanical load-bearing applications. #2 Hard or Silver Soldering (above 450 °C) The first step of cleaning an oxidized soldering iron tip is to unplug the device from its power source. Once disconnected from the power source, rub the tip with a damp cloth or sponge to remove any dirt or debris that may have accumulated on its surface. After wiping down the surface, use a brass brush or cleaning pad with some rubbing alcohol and gently scrub away any oxidation that has built up on the tip. If needed, hold the soldering iron under running water while using a bristle brush for stubborn oxidation spots. Cleaning a Weller Soldering Iron Tip

Step 3: Wipe the tip of the soldering iron on a damp wet sponge to clean it. Wait a few seconds to let the tip heat up again before proceeding to step 4. Cleaning your soldering iron tips is an essential part of caring for your soldering equipment. Soldering iron tips work best when they’re clean, so you should make sure they are bright and shiny before, during and after you use them. Solder is a metal alloy with a low melting temperature point, used alongside a soldering iron to permanently join together two metals with a higher melting point. The majority of solder comes in the form of a coiled length of wire, or less commonly as pellets, with a range of diameters or gauges available to suit various applications and joints. While I’ve previously dived deep into the science of cleaning soldering irons, the ongoing debate between using a soldering sponge or brass wool for tip maintenance still draws interest. Operator fatigue is less compared to the welding process. Soldering is divided into two classifications: soft and hard.

Soldering Iron tips do not last forever. Eventually they wear out. Common signs that the tip needs replacing are: a hollow forming in the end of the tip, cleaning and re-tinning has no effect, or needs frequent repeating.We rate each method on a scale of low, medium, and high for each indicator. For example, Method 1 (solder tip cleaner) is rated as high for effectiveness, high for ease of use, low for cost, high for durability, and high for portability. Some brass cleaners have a thin coat of flux applied to the brass wire that helps to clean and tin the tip. Step 4: Hold the soldering iron in one hand and solder in the other. Touch the solder to the tip of the iron and make sure the solder flows evenly around the tip. Step 2: Turn on your soldering iron and let it heat up. If you have a soldering station with an adjustable temp control, set it to 400′ C/ 752′ F. The solder, which is mostly composed of lead and tin, has a melting range of 150 to 350°C. A suitable flux is always used in soft soldering.

You must wear protective eyewear when doing soldering, to protect from an accidental splash of hot solder.While it’s important to keep your tips clean, you also need to remember to clean the components you will be working on. Before you begin soldering, use alcohol and a clean cloth to remove grease, dirt and oxidisation from the surface you will be soldering. When buying solder, make sure NOT to use acid core solder as this will damage your circuits and components. Acid core solder is sold at home improvement stores and is mainly used for plumbing and metal working. As with all DIY activities involving potentially hazardous tools or conditions, safety awareness should always be a top priority in preparing for soldering work. As ever, this includes making sure that you’ve got the right PPE equipment in place prior to starting the job. It also means ensuring that the surrounding area is well-prepared and as free from unnecessary hazards as practically possible.